•
These Gemstone Alignment Blocks are made of solid steel and they are milled to exact specifications to give you a flat smooth surface to set your girdle facet on after transfering your gemstone. It gives you the advantage of being able to see as well as feel that your gemstone is realigned to the correct index setting after transfering your gemstone from the first dop to other.
More info ››
•
The Mag Dop is a tool that is easily used for dopping that piece of expensive rough. It lets you easliy position your gem rough to the precise center so that you can optimize your gemstones return when faceting.
More info ››
•
This Stop Indicator Bracket is a Best Cut Gems exclusive. The Stop Indicator Bracket is custom made for your Ultra Tec Faceting Machine, to enable you, to hold your Ultra Tec Stop Indicator (Buzzer/Light), SKU# UT-908, up at eye level, making it easier to read and it doesn't take up valuable table space either.
More info ››
•
This provides two inches of extra height for the Mast while maintaining its firmness. It's for cutting very large stones. Now, for an occasional large stone, the 90° Table Adapter can be used, but you have to scrunch down to view the Table. So, if you do many large stones, the Two-Inch Base lets you work comfortably...........
More info ››
•
Extra Blades for your Ultra Tec Saw Kit. .012 is a more ridged blade.
More info ››
•
We offer a large range of DOPS in Flat (F), Cavity (C), and V configurations. Standard F and C Dops are keyed, while V Dops are not--(because long-sided stones, like those cut in the V dop, are best aligned using the long girdle facet--but if you insist, there are keyed..............
More info ››
•
With all other accessories, we recommend waiting until you have been faceting for a while--to see which you want--but, we recommend the Dial Indicator Attachment immediately--we think it's an "everyone-should-have" accessory. In faceting, the "action" occurs between the stone and the lap, where you can't see it. Using a Dial Indicator Attachment, however, is like having "eyes on the lap"............
More info ››
•
THE NEW ULTRA TEC DIGITAL ANGLE DIAL! It is finally here! Extraordinarily accurate and repeatable to .01 degrees. The Ultra Tec Digital Angle Dial is expected to be ready for shipment by October, 2008. The Ultra Tec Digital Angle Dial can be installed by the faceter.
More info ››
•
Ultra Tec Dop Retention Screw, This is the brass set screw that holds your dop in place.
More info ››
•
12 Dops - 2, 3, 4, 5mm
Flat, Cone & Vee Brass Dops.
More info ››
•
Protect your equipment and the lap surface from airborne grit--and avoid "mystery" scratches. Made of flexible 4 mil vinyl, and imprinted with the Ultra Tec logo.
More info ››
•
8 Dops - 5X2.5, 6X3, 8X3.5, 9.5X4 - Flat & Vee or 6 Dops - 12.5X5.3, 16X6, 19X9.5 - Flat & Vee
More info ››
•
Save your precious rough and time with this handy saw kit. Fast, saves your laps and saves your material! Once you try it you will wonder how you faceted without it.............
More info ››
•
We offer a large range of DOPS in Flat (F), Cavity (C), and V configurations. Standard F and C Dops are keyed, while V Dops are not--(because long-sided stones, like those cut in the V dop, are best aligned using the long girdle facet--but if you insist, there are keyed..............
More info ››
•
The Guiu Dopper is an accessory that lets you set your dop in an optimum position on the rough, to assure maximum yield. You position and control the rough relative to the dop mechanically—precisely (the picture tells the story better than words). The depth of insertion of the rough is settable, and then X and Y positioning is easily done. No more “eyeballing” it in. As you well know............
More info ››
•
Guiu Girdle Aligner—a parallel bar 2 inches long that can be affixed to your stone to allow you to adjust girdle position after transfer to almost perfect. The long bar allows a much better straight edge to align to.
More info ››
•
The Ultra Tec Faceting Machine comes with a 96 Index Gear--the most often used. Faceting designs specify the Index Gear, and the 96 and 64 cover about 80% of published designs. Changing Index Gears takes only a few minutes. The symmetry of a design depends on which numbers divide evenly into the available number of teeth on the Index Gear. For example, a 5-sided design.............
More info ››
•
There is a stud, that holds the Lamp, preassembled at the rear of the Baseplate . The Lamp's vinyl-coated gooseneck is 30 inches long, allowing easy location of the illumination relative to the facet surface. The Lamp accepts a 100 watt bulb. The double walled shade stays cool on the outside, avoiding accidental burns.
More info ››
•
This allows the preforming of Marquise, Oval and Shield shapes. Fitting onto the outside diameter of the Spindle, it provides up to 30mm of offset, calibrated in increments of .1mm. Four keyed dops are included. Instructions include tables for standard stone sizes, and a method for calculation of offset for any combination you'd like--You should understand that preforming is not an absolute necessity...........
More info ››
•
Developed for tables, but OK for any facet--it's slow, but accurate. It maintains steady speed and arc on the lap. At times, impatient people, finding a large table isn't polishing "fast enough" decide to "lean a little extra". The next thing they find is a new table advancing across the stone. So, if you're impatient--develop some patience, or stop cutting such big stones, or get an Oscillator and let it do the work............
More info ››
•
It rotates the Spindle at a constant speed for round pre-forming. It's slower than you can do it, but it works while you're doing something else, and doesn't fatigue. It makes the preform very accurately round, using the Angle Stop to control the depth of the cut. It installs and removes easily.........
More info ››
•
The Stop Indicator signals contact with the stop, offering both a sight signal and a sound signal--a red-light comes on when contact has been made with the stop, and also a buzzer (which is optionally-on) The buzzer feature................
More info ››
•
This provides fast, accurate alignment of the Tabling Adapter. It is inserted into the Tabling Adapter and is used to align the adapter flat to the lap. It eliminates the effect of tolerance build-up, and when the Adapter is replaced by the dopped stone, it's right on right angle.
More info ››
•
5X2, 6.4X2, 8X2,9.5X2.2MM - Flat & Vee or 12.7X2.5, 15.9X3, 19X4.5MM - Flat & Vee
More info ››
•
We offer a large range of DOPS in Flat (F), Cavity (C), and V configurations. Standard F and C Dops are keyed, while V Dops are not--(because long-sided stones, like those cut in the V dop, are best aligned using the long girdle facet--but if you insist, there are keyed..............
More info ››
